2 × 5 liters
The contents are clearly stated on this page. You will receive Snow Foam V2 concentrate; accessories are available separately.
DOUBLE CONCENTRATED V2 · PRE-WASH · 2 × 5L · 10 LITERS
10L
Total content
V2
Double concentrated formula
3–5
Minutes to work in, without drying out
Pre-wash
Before hand washing
A GOOD WASH STARTS BEFORE THE RUBBING
First loosen the dirt. Only then use a wash mitt.
You want to remove as much sand and road grime as possible before touching the paint. The foam layer helps loosen that dirt so you can spray it off first.
Less mess while washing your hands
The pre-wash removes as much loose dirt as possible. This helps reduce the risk of swirl marks during washing.
Double concentrated V2
The V2 formula is twice as concentrated as the previous Nanoglans formula. Adjust the dosage according to your device and the level of soiling.
Also for matte paint and wraps
Suitable for matte paint, wraps and coated surfaces when used correctly. Work on a cool surface and never let the foam dry out.
THIS IS WHAT YOU RECEIVE
Two jerrycans. Ten liters of supply.
You are ordering one complete duo pack with 2 × 5 liters. Your order therefore contains 10 liters of product.
For regular washing
Dispense only what you need for each wash. How long your supply lasts depends on your vehicle, foam cannon, and the level of dirt.
The right combination
Use a suitable Foam Cannon on your pressure washer, a hand foamer, or an e-Foamer. The foam you produce also depends on the settings.
HOW TO USE NANOGLANS SNOW FOAM
Foam. Work into. Rinse thoroughly.
Work out of direct sunlight, on a cooled vehicle. Also follow the instructions on your packaging and from your foamer.
1. Foam your dry car
Apply the foam to a dry car, without rinsing it beforehand. This allows the foam to attach to the dirt.
2. Leave to work for 3–5 minutes
Give the product time to loosen the dirt. Keep an eye on the surface: do not let the foam dry out and rinse off sooner if necessary.
3. Spray off and wash after
Rinse thoroughly with your pressure washer. Then wash with Fantastic Shampoo and a clean wash mitt to remove any remaining dirt.
DOSE FOR YOUR DEVICE
How to mix your Snow Foam.
| Foam Cannon / high pressure | 100–150 ml of product per approximately 900–1,000 ml of water. Take your reservoir’s capacity into account. |
|---|---|
| Hand Foamer / e-Foamer | 50–80 ml of product per approximately 1.5 litres of water. Adjust according to the appliance, soiling level and label. |
| Foam Gun with Gardena connection | Fill the product reservoir with pure Snow Foam and set the dosing knob to position 1. |
| Processing time | 3–5 minutes; never allow to dry out. |
| Substrate | Dry, cooled car. Not in direct sunlight. |
| Packaging | 2 × 5L · 10 liters |
| Formula | Snow Foam V2, double concentrated. |
GET MORE OUT OF YOUR FOAM
A better pre-wash starts with the right approach.
Even contact with the dirt and the correct dwell time matter. A thicker layer of foam alone doesn't tell the whole story.
Work cool and out of the sun
The foam dries faster on warm panels. Let the car cool down first.
Set up your foamer properly
Water pressure, nozzle, water hardness and dosage affect the foam. Start with the recommended dosage.
Don't forget to wash your hands
Foam is the pre-wash. Stubborn road film may require a hand wash with a suitable shampoo.
Do you want to protect too?
This Snow Foam is intended for cleaning. For a separate protective layer, use a suitable protection product after washing.
DOSAGE, USE AND PACKAGING
Your questions about Snow Foam V2.
Clear answers for your next wash.
How many liters are in this package?
This duo pack contains two 5-liter jerrycans: 10 liters in total. The old URL still states 2.5 liters; the current packaging is 2 × 5 liters.
Why should I use Snow Foam before hand washing?
The foam helps loosen sand, dust and road grime. By spraying first, less loose dirt will get under your wash mitt.
Does my car need to be dry or wet?
Apply the foam to a dry, cooled-down car. Do not rinse it beforehand. Work out of direct sunlight and do not allow the product to dry out.
How long should the Snow Foam work for?
Leave to work for 3–5 minutes and then rinse thoroughly. Rinse sooner if the surface is at risk of drying out.
How much product do I use in a foam cannon?
As a guideline, use 100–150 ml of product per approximately 900–1,000 ml of water. Do not exceed the maximum capacity of your reservoir and follow the label. The correct setting depends on the device and the level of soiling.
Can I use this Snow Foam on matte paintwork, wraps, and coatings?
Yes. Nanoglans Snow Foam V2 is designed to clean these surfaces when used correctly. Follow the instructions and do not allow the foam to dry.
Do I still need to wash it by hand afterwards?
For a completely clean car, we recommend a hand wash after the pre-wash. For example, use Nanoglans Fantastic Shampoo with a clean Nanoglans wash mitt.
Does this Snow Foam also provide a coating?
This Snow Foam V2 is a cleaning pre-wash. If you want to apply a separate protective layer after washing, choose Nanoglans Coating Spray, for example.
COMBINE WITH NANOGLANCE
From pre-wash to the last drop.
The next steps in your skincare routine. These products are sold separately.
AFTER PREWASHING
Fantastic Shampoo V2 · 1L
For hand washing after rinsing off the foam. Use with a clean wash mitt.
FOR YOUR HAND WASH
Microfiber Washcloth Duo Pack
Wash with clean microfiber cloths and rinse the wash mitt thoroughly in between.
AFTER RINSING
XXL drying cloth · 60 × 90 cm
Dry your car after washing with soft 1600 GSM coral fleece.
Snow Foam 2× 5L – Duopack Value Pack 10L
Sale price
€89,99
Regular price
€120,00